Epoxy Garage Flooring in Hollywood, FL
Epoxy garage flooring in Hollywood, FL turns a bare, stained concrete slab into a sealed, glossy surface that is easier to sweep, mop and live with. The coating is only as good as the concrete under it, so most of the job happens before any epoxy is mixed. The slab is checked for moisture, ground or etched, and repaired first.
Common Problems That Require Epoxy Garage Flooring
What bare concrete does over time
Concrete looks solid, but it is full of tiny pores. Motor oil, brake fluid and coolant sink into those pores and leave dark stains that scrubbing barely touches. The top layer of a slab can also wear down into a powdery dust, which then gets tracked into the house on shoes and pet paws.
Many homeowners first notice the floor when they clear out the garage. Underneath the boxes is a patchwork of stains, a few hairline cracks and a rough strip where the car tires sit. None of that is dangerous, yet it makes the garage hard to keep clean and hard to use as a workshop or laundry space.
Why coatings peel and fail
A failing coating usually comes down to one of three things. The first is weak preparation. Epoxy rolled onto smooth, dusty or oily concrete has nothing to grip, so it lets go in sheets. The second is moisture. Water vapor moving up through the slab builds pressure under the coating and can push it loose in bubbles and blisters. The third is heat from tires. A car that has just come off a hot road can soften a thin or poorly bonded coating, and the tires lift it when you drive away. People call this hot-tire pickup, and it is a common complaint with store-bought paint-on kits.
Why it matters in South Florida
The air around Hollywood stays humid for much of the year, and many homes here sit on concrete slabs poured right on the ground. Both of those affect how a coating cures and how well it holds. A floor that looks dry at noon can still be carrying moisture, which is why a moisture check comes before anything else. If the door itself is sticking or noisy, it makes sense to sort out garage door repair while the garage is already cleared out.
What Does Epoxy Garage Flooring Involve?
Looking at the slab first
The first visit is about the concrete, not the color chart. The floor is checked for cracks, chips, crumbling edges, old paint or sealer, and signs of trapped moisture such as white powdery deposits or dark damp areas. A simple test is to tape a square of plastic sheet to the slab and look underneath after a day. Beads of water under the plastic point to moisture that a coating will have to deal with.
The age of the slab matters as well. Fresh concrete needs time before it can be coated. One manufacturer's data sheet, for Rust-Oleum's water-based EpoxyShield garage floor coating, says new concrete should cure for at least 28 days first and that the product is not meant for floors with a moisture problem. Other coating systems set their own limits, so the product chosen for your floor decides the exact rule.
Grinding or etching the surface
Epoxy needs a rough, clean surface to bite into. Most concrete floors have to be ground with a diamond grinder or etched with an acid solution before coating. Grinding also removes old paint and the smooth, weak top layer. Afterward, the dust is vacuumed up and the slab is cleaned so nothing sits between the concrete and the first coat.
Fixing cracks and chips
Cracks, pits and broken edges are filled and leveled before any coating goes down. A coating spread over a crack will usually show the crack again later, so this step affects how the finished floor looks for years.
Coats, flakes and finishes
A typical system starts with a base coat that soaks into the prepared concrete. While it is still wet, colored vinyl flakes can be broadcast across it for a speckled, textured look that hides dust and small marks. A clear top coat then seals everything in. A metallic finish is a different look, with swirling pearl-like color and a high shine, and it takes more material and more careful work.
Patching an existing coating
If an older epoxy floor has only a few chipped spots and is still bonded everywhere else, those areas can sometimes be cleaned, roughened and touched up. That only works when the rest of the coating is sound.
When the old coating has to come off
When a coating is peeling in large areas or lifting under the tires, patching rarely lasts. The loose material is ground off down to bare concrete and the floor is coated again from the start, including a fresh look at the moisture question that may have caused the failure.
Curing time and fumes
Every product has its own cure schedule, and temperature and humidity change it. The same Rust-Oleum data sheet lists 24 hours before foot traffic and 3 days before vehicle traffic at 70 to 80°F and 50% relative humidity. Other epoxies differ, and humid weather can stretch the wait. Keep children, pets and cars off the floor until the installer says it is ready, and leave the garage ventilated while the coating cures.
How Much Does Epoxy Garage Flooring Cost?
We couldn't find a verified price range for Hollywood or for Florida, so the figures below are national ranges from published cost guides. They cover professionally installed floors, materials and labor included.
| Job | Typical range |
|---|---|
| Installed epoxy floor, per square foot | $3–$12 per sq ft |
| One-car garage floor (about 200 to 240 sq ft) | $720–$2,900 |
| Two-car garage floor (about 360 sq ft) | $1,100–$4,300 |
| Three-car garage floor (about 700 sq ft) | $2,200–$9,500 |
| Metallic epoxy finish, per square foot | $5–$12 per sq ft |
Sources: national figures from Bob Vila, This Old House and Today's Homeowner, checked November 2026.
What pushes the number up or down
Floor size is the obvious factor, but the condition of the concrete often matters just as much. A clean, sound slab needs far less prep than one with wide cracks, old peeling paint or a moisture issue that has to be addressed. The finish counts too. A solid color with a clear coat costs less than a full flake broadcast, and a metallic floor sits toward the top of the range. Moving shelves, stored items and appliances out of the way can also add time if the garage is full.
The price for your garage depends on its size and what the slab inspection shows. It is set by an estimate after the floor is looked at, and the ranges above are not a quote.
Why Choose NovaLift Garage Doors?
NovaLift Garage Doors is a Hollywood company that already spends its days in garages, and epoxy floor coating is one of the services it offers. That means one call can cover the floor and, if you need it, the door that sits on top of it.
Before you pick colors or flakes, you hear what the slab inspection found. If a moisture concern or a set of cracks will change the plan, you are told plainly and the estimate reflects it. You make the choices about finish and timing, and nothing is started until you agree. Call (954) 758-9013 to talk it through.
Our Epoxy Garage Flooring Process
- Tell us about the garage
Call or use the form. Let us know the rough size of the garage, whether the floor has paint or a coating on it now, and the look you have in mind.
- The slab is inspected and tested
Cracks, chips, old coatings and signs of moisture are checked, and the age of the concrete is confirmed before a system is chosen.
- You get options and an estimate
You see the finish choices, what prep the floor needs and an estimate for the work before any grinding starts.
- The concrete is prepared
The floor is ground or etched, cleaned of dust, and every crack and chip is filled and leveled.
- Coats and finish go down
The base coat is applied, flakes or a metallic effect are added if you chose them, and a clear top coat seals the surface.
- The floor cures before use
You are given the cure times for the product used, and the garage stays clear until the floor can take foot traffic and then a car.
Frequently Asked Questions About Epoxy Garage Flooring
Will an epoxy coating hide the cracks in my garage floor?
Not on its own. Epoxy follows the surface it sits on, so an open crack tends to show through or reappear. Cracks and chips are filled and leveled during prep, which is what gives the finished floor its smooth look.
Can epoxy go over the paint already on my floor?
Usually it shouldn't. Old paint or a worn coating is a weak layer, and new epoxy is only as strong as what it bonds to. The old material is normally ground off so the new coating grips bare, clean concrete.
Is an epoxy garage floor slippery when it gets wet?
A smooth, glossy epoxy can be slick with water or oil on it. Broadcast flakes add texture, and an anti-slip additive can be mixed into the top coat for more grip, which is worth asking about if the garage doubles as an entry to the house.
How soon can I park my car on a new epoxy floor?
It depends on the product and the weather. One manufacturer's data sheet lists 3 days before vehicle traffic under mild conditions, while other systems are faster or slower. Humid days can lengthen the wait, so go by the cure time you are given for your floor.
Do I have to empty the garage completely?
Yes, the floor needs to be clear from wall to wall. Grinding, coating and curing all need open space, so cars, shelving, bins and anything stored on the floor have to come out until the coating has cured.
How do I keep an epoxy floor clean?
Sweep or dust-mop it often and wash it with water and a mild cleaner. Grit is what dulls the top coat over time, so a mat at the door and quick cleanup of oil or fluid spills keep the surface looking newer for longer.
Other garage door services
- Garage Door Repair
- Garage Door Spring Repair
- Garage Door Opener Repair
- Garage Door Cable Repair
- Garage Door Off-Track Repair
- Garage Door Installation
- Garage Door Roller Replacement
Epoxy floors near Hollywood
Epoxy garage floor coating is also available in each of the cities around Hollywood:
Request Epoxy Garage Flooring in Hollywood
Call NovaLift Garage Doors to talk about your floor and the finish you want, or send your address and a short description through the contact page.